Barclay Products TKCTR7H67-SN4 Guide d'installation télécharger pdf

INSTALLATION INSTRUCTIONS

P 847•244•1234 www.barclayproducts.com

4/14/09

Parts Included

• 1 Valve Body • 1 Hose • 1 Cradle • 1 Elephant Spout • 3 Washers • 2 Cone Washers

2 Large Locknuts • 2 Connecting Nuts • 2 (2 1/4”) Threaded Nipples • 60” Riser • 6” Wall Support

● 1Sunflower Showerhead ●

Tub Filler with

Diverter, Hand Shower

and Shower Ring

Tools Needed

• Adjustable Wrench • Slip Joint Pliers • Pipe Putty or Teflon Pipe Tape •

• 2 Mounting Flanges Needed • Offset Bath Supplies #5576 •

NOTE: Handles are identified HOT and COLD. The hot handle must be to the left and cold to the right.

Be sure the water supply is turned off before starting installation. Cushion the wrench or slip

joint pliers with an old cloth to protect the finish of the fixture.

Cat. No.

4063

To Connect Shower Set to Tubes

Offset Bath Supplies #5576 Installation:

1. If you purchased the brass water supply tubes, first remove the round rubber washer from the end

of each water supply tube.

2. Put the cone washers on the tub and connect the end of each water supply tube. Then slide

the 1/2” connecting nuts over the opposite ends of the supply tubes and up to the cone washers.

3. Twist the connecting nuts over the cone washers and thread the nuts onto the nipples.

4. Connect the other ends of the brass water supply tubes to your house water lines.

Consult your local plumber for assistance.

5. Repeat steps 1-4 using the right supply tube.

To Install Tubes

1. Align the valve assembly with the mounting flanges and secure with the nuts on the mounting flanges. Tighten

with a wrench or pliers. NOTE: Flanges may be positioned up or down, depending on how high you want the spout.

2. Apply teflon tape to both ends of the hot and cold supply nipples. Thread the tapered ends of the nipples into the

mounting flanges. On the outside of the tub, thread the large locknuts onto the other ends of the nipples and secure

the shower set to the tub.

3. Thread diverter valve onto valve assembly.

4. Position cradle bracket on riser. Tighten with set screw.

5. Install washers in the hose ends and attach the hose to the cradle and shower head. (DO NOT over tighten)

6. Connect the water supply nipples to the brass water supply tubes. For wall mounting of the shower set to a house

water supply line, see your local plumber.

7. Slip the wall bracket over the straight end of the riser pipe. Carefully slide the bracket to the appropriate position

(approximately half-way up the rod) and tighten the set screw provided.

8. Assemble riser pipe to the riser coupling assembly on the spout by tightening the coupling nut. After hand

tightening, fasten securely by using a wrench.

9. Secure wall support bracket to the wall using the screws provided with part #4195WS.

NOTE: Please seek professional help if you have copper plumbing in your home.

Cleaning Instructions

Wipe this whole set off with warm water and a soft cloth. DO NOT use soaps, cleansers, or brass cleaners as

they will disintegrate the protective lacquer coating and leave the brass exposed causing it to tarnish.

Pg. 1

1 2 3 4 5

Résumé du contenu

Page 1 - Diverter, Hand Shower

INSTALLATION INSTRUCTIONSP 847•244•1234 www.barclayproducts.com4/14/09Parts Included• 1 Valve Body • 1 Hose • 1 Cradle • 1 Elephant Spout • 3 Wa

Page 2

1. Connect both halves of the curtain frame (1) using the ceiling tees and wall tees as shown above. In order to insure a solid fit, the tees fit s

Page 3 - Supplies

ASSEMBLY INSTRUCTIONSP 847•244•1234 www.barclayproducts.com3/22/121. First be sure to shut off the the water supply. Remove old water supply tubi

Page 4 - Straight Bath

INSTALLATION INSTRUCTIONSP 847•244•1234 www.barclayproducts.com3/17/08To Assemble Tubes1. First be sure to shut off the the water supply. Remove

Page 5

INSTALLATION INSTRUCTIONSP 847•244•1234 www.barclayproducts.com1/8/08To Assemble Tubes1. Assembled #3 and #8 screw into #2. #7 is on top of #2 be

Commentaires sur ces manuels

Pas de commentaire

Barclay Products TKCTR7H67-SN4 Guide d'installation

Naviguer en ligne ou télécharger Guide d'installation pour Articles sanitaires Barclay Products TKCTR7H67-SN4. Barclay Products TKCTR7H67-SN4 Installation Guide Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Articles sanitaires Barclay Products TKCTR7H67-SN4